Installing the MrCool DIY is an easy process that should only take a few minutes. Before you begin, you will need to make sure you have the necessary tools and materials that may be required. Depending on the configuration of the unit, you may need a number of different tools and materials such as, a Phillips head screwdriver, a flat head screwdriver, pliers, wire cutters, conduit, duct tape, and screws.
Step 1: Make sure to clean the area where the unit will be installed. This will ensure that you don’t get any dirt in the unit, and that the unit will be properly sealed and functioning properly.
Step 2: Unpack the unit and read the instructions carefully. Pay special attention to the instructions regarding the power source and wiring set up. Be sure to follow all the instructions carefully, and double-check your work.
Step 3: Connect the unit to the power source. By connecting the unit directly to the power source, you will be able to use the unit immediately after installation. This means you can use the unit directly after installation.
Step 4: Secure the unit. You will need to use screws and/or other fasteners to securely mount the unit to the surface where you are installing it. Be sure to use the supplied fasteners and screws, as doing so will help ensure the unit stays in place and is not damaged.
Step 5: Connect the ducting. The ducting should be connected using screws, wire ties, and/or staples, depending on your configuration. Make sure the ductwork connections are secure, and that the unit is sealed properly.
Step 6: Turn the power on at the circuit breaker. After you have performed all the necessary steps, you can now turn the power on and the unit should now be installed and ready to use!
Is MrCool easy to install?
Yes, MrCool is easy to install. It comes with detailed installation instructions and all of the necessary hardware, so you won’t need to purchase any extra components. Typically, installing MrCool is as simple as mounting the evaporator in a fan coil cabinet, connecting the two main lines, setting the thermostat, and providing power to the unit.
This type of installation requires no special tools or expertise and can usually be done in most locations within a few hours. For more complex installations like multi-zone systems and ductless systems, the process is only slightly more involved and will require the help of an experienced contractor.
Does MrCool come with electrical wiring?
No, MrCool units do not come with electrical wiring. You will need to have any necessary wiring done by a licensed electrician prior to installation of your MrCool unit. This includes a dedicated electrical circuit and a dedicated 15 to 20 amp GFCI-protected circuit breaker.
The wiring will connect the indoor HVAC unit to the outdoor unit. If the existing wiring is inadequate, it will be necessary to install additional outlets and/or circuits. When working on any electrical components, it’s essential to ensure safety, so having a licensed electrician perform the work is the safest and most reliable option.
What size breaker for MrCool mini split?
When installing a MrCool Mini Split, the proper breaker size depends on the model of the system being installed. For example, the 18,000 BTU Classic+ Mini Split system requires a 2 pole 30 amp breaker with 10 gauge wire, while the 24,000 BTU Classic+ Mini Split requires a 2 pole 40 amp breaker with 8 gauge wire.
The specification sheets for each model can provide additional details about wire and breaker size requirements. It is important to use the correct size and type of breaker to ensure safety and proper operation of the system.
It is also important to consult with a qualified contractor in order to properly size and install the breaker and system according to the manufacturer’s specifications.
Can I install a mini split myself?
No, it is not recommended to install a mini split yourself. Although it may appear to be a straightforward installation, mini splits are complex systems and require professional installation in order to ensure proper operation and system efficiency.
Specialized tools are required to properly maneuver the unit and its many components. Additionally, there may be local building codes or other regulations to consider, such as zoning laws or setback requirements, when installing a mini split.
Even for experienced homeowners, it is important to contact a qualified and experienced HVAC contractor to get the job done safely and correctly.
Does a mini split need its own breaker?
Yes, a mini split does need its own breaker in the electrical panel. The type and size of breaker you need will depend on the size and number of mini split units you will have installed. Typically, a 15-amp breaker is required for individual units that use 1.
5 to 3 tons of cooling, while a 20-amp breaker is required for units that use more than 3 tons of cooling. It is important to have the proper sized breaker to avoid overloading the electrical panel, as this can cause serious damage to the unit, as well as potential fire, shock, or other hazards.
In addition, having the right sized breaker can also ensure that the unit functions properly and efficiently. It is recommended to consult with a licensed professional who specializes in mini split systems to confirm the correct sized breaker.
Does a mini split plug into an outlet?
Yes, a mini split air conditioner can be plugged into a standard 120 volt electrical outlet. The specific power requirements of the mini split will vary depending on the make and model, so you should consult the owners manual or installation manual for your model.
Most mini splits require a dedicated circuit and should not be connected to an extension cord. Additionally, it is important to ensure that the power requirements for your system are compatible with the capacity of your electrical outlet.
For example, if your mini split requires a 30-amp outlet, but your home only has 20-amp outlets, you will need to install additional outlets or update existing ones to meet the requirements of the mini split.
It is important to take care during the installation process, as the mini split is connected to power mains and the electricity can be highly dangerous if mishandled.
Do mini splits have to be wired in?
Yes, mini splits typically must be wired into a functioning electrical system. In order to ensure that the mini split system operates correctly and functions safely, it is important to ensure that it is correctly wired.
An experienced electrician should install the wiring and connections for the mini split system, making sure that all electrical connections adhere to legal and local codes and regulations. It is not recommended that homeowners or untrained persons attempt to wire their own mini split system, as the results could be potentially dangerous and could void the warranty of the system.
What wiring is needed for a mini split?
In order to set up a mini split system, certain wiring is required. Generally, a dedicated circuit must be installed with 10 gauge wires that are at least three feet long in between the unit and the breaker.
This will create a reliable connection and ensure the safety of the system and its users. The circuits must also be GFCI protected and outdoor units must be connected with a weather-proof cable.
Other components that may need to be wired include the thermostat, contactor, fan motor, compressor, drain lines, and remote control. The thermostat should be connected with at least 18 gauge wiring, the contactor should be connected with at least 14 gauge wiring, the fan motor needs to be wired to the contactor, the compressor also needs to be wired to the contactor, the drain lines need to be connected with a trap, and the remote control should be wired with the fan motor and compressor.
In order for the mini split system to function effectively, it is important that all of the wiring is done properly and in accordance with local building codes and safety regulations. An electrician should be consulted when planning the installation of a mini split system to ensure the safety and proper electrical connections.
Do MRCOOL units come pre-charged?
No, MRCOOL units do not come pre-charged. The installation process requires manual charging, which will take up to one hour and must be done by a qualified service technician. In order to complete the installation properly, you must ensure the manager provided with the installation has all indoor and outdoor components, with the refrigerant already in the outdoor condenser unit.
Additionally, the system must be connected to a power source and given enough time for the system to reach its normal operating temperature. During the installation process, it is important to check the pressure gauge readings to ensure the system is correctly charged and working at its optimal performance level.
It is also important to use high-quality cycling components, such as filter dryers, that are appropriately sized to meet the manufacturer’s requirements.
How much does it cost to install MRCOOL mini split?
The cost of installing a MRCOOL mini split system can vary greatly depending on the type and size of system being installed and the complexity of the installation job. Factors that affect the overall cost of installation include the location of the home or business, ease of access to the area of installation, local labor and material costs, and additional features like insulation, ducting, zoning, and prior conditions that may be present.
Generally, installation of a basic 1 or 2 head mini split system in an easy to access, straight forward location with no additional features would run anywhere from $1,500 – $2,500. However, if a home or business has complex floors, walls or exists that require additional ductwork, insulation, or zoning the cost of installation can increase significantly.
What happens if you don’t pull a vacuum on a mini split?
If you don’t pull a vacuum on a mini split, you run the risk of the HVAC system having too much air and moisture in the system. This can damage the system’s components and decrease the overall efficiency of the system.
Too much air and moisture can reduce the refrigerant flow and cause “slugging” of the compressor. Compressor slugging can cause the compressor to fail and/or reduce capacity. The excess air and moisture in the system can also increase the system’s discharge pressure, leading to compressor damage or even failure.
Additionally, contaminants can build up in the system, leading to increased friction, system clogging, and other permanent damages that can reduce the system’s efficiency. Pulling a vacuum on the mini split is a critical step in prepping the system, as the vacuum helps remove any excess moisture and air, and helps to ensure proper operation and performance.
Does MRCOOL run all the time?
No, MRCOOL units do not run continuously. MRCOOL units come with a range of cooling options, and you can select the one that most suits your needs. For more economical use, each unit has software-controlled settings, allowing you to customize your cooling times and temperature preferences.
This way, the unit can shut off automatically when the set temperature is reached, saving energy and resources. Additionally, all MRCOOL units come with a Sleep Mode feature that runs quietly and efficiently overnight, allowing you to sleep comfortably.
With these features, you can be confident that your air conditioner isn’t running all of the time.
Where should you not install a mini split?
Ultimately, a mini split can be installed in almost any room as long as the conditions are right. However, it is generally not advisable to install a mini split in an area that is damp, humid, or extremely dusty, such as a basement or a bathroom.
Additionally, a mini split should never be placed by a pool or other source of water, as this could cause major electrical system problems if the water were to come into contact with any of the components.
Furthermore, if you plan on installing a mini split outside, you want to make sure it is sufficiently shielded from the elements like direct sunlight, rain, and snow as too much of any of these can be detrimental to the mini split system.
What are the disadvantages of a mini split?
Mini split systems are a popular choice when it comes to air conditioning, but they come with both advantages and disadvantages. The following are some potential disadvantages of a mini split system:
1. Initial cost: Mini splits can be quite expensive due to the costs associated with ductwork, multiple indoor units, and the outdoor condensing unit. They also require specialized installation, which can add to the cost.
2. Maintenance: In order to ensure peak performance of a mini split system, periodic maintenance is required to replace air filters and inspect air handler components. This can be expensive and time consuming.
3. Unsightly outdoor units: While outdoor units of mini split systems are less visible than traditional air conditioners, they are still quite large and can be unsightly depending on the model.
4. Poor energy efficiency: Some mini split systems are not as energy efficient as traditional systems, so you may pay more in energy costs each month.
5. Limited cooling capacities: Mini split systems are limited in their capacity to cool large areas as compared to larger traditional AC systems.
6. Poor air circulation: The design of a mini split system can be limited in its ability to evenly circulate air throughout the home or business. This can lead to large hot and cold spots, as well as increased humidity levels.