The T500 still takes an average of 30 minutes to distill a single batch of liquor or spirits. During this time, it produces a yield of up to 500ml of high-proof, flavor-infused spirit. The T500 is composed of two main components – the tank and the boiler, both of which enable efficient and rapid distillation of your choice of spirits and liqueurs.
The tank is filled with water and connected to the boiler. The liquid is then heated and circulated on a specific cycle, which helps to create a distillate that is both high in alcohol content as well as in flavor and aroma components.
The distillate is then cooled and collected in the waiting container. Depending on the type of liquor or spirit being distilled, additional flavoring ingredients may be added in after the distillation process is completed.
How do you make distilled water with T500?
Distilling water with the T500 is a simple process that is done in a few easy steps.
1. Fill the T500’s water reservoir with tap water up to the Max water line.
2. Place the collector bowl onto the center of the machine and then place the lid on top to cover the collector bowl, leaving the steam port open.
3. Plug the machine into an outlet and turn it on.
4. The heat from the T500 will cause the water to boil and form steam.
5. The steam will rise, condense on the lid, and then drain through the steam port, down the tubing, into the collector bowl.
6. The condensed water will collect in the bowl in its purest form, known as distilled water.
7. Allow the device to run until the reservoir is drained and the light informs you that it is time to refill.
8. Turn off the device and wait for the machine and bowl to cool before refilling.
9. Repeat the process until the desired amount of distilled water has been collected.
How much alcohol does a Turbo 500 still produce?
The amount of alcohol a Turbo 500 still produces depends on many factors, including the type of mash being used, the temperature of the distillation, the base alcohol used, and the length of distillation time.
Generally speaking, a Turbo 500 still can produce a maximum of 96% ABV without modifications. However, the still can produce anywhere between 50-95% ABV depending on the parameters chosen and how long you run the still.
Additionally, if you blend your finished distillate with additional water, you can reach an ABV that is lower than 50%. Ultimately, the amount of alcohol a Turbo 500 still produces is up to the distiller.
How much alcohol do you get from a 25 Litre wash?
The amount of alcohol that you can get from a 25 Litre wash depends on several variables, including the type of fermentation process used, the starting specific gravity of the wash, and the amount of time that the wash is allowed to ferment.
Generally speaking, a wash with a starting specific gravity of 1. 050 will yield an approximate alcohol content of 5% – 6%. However, this can vary significantly depending on the fermentation process.
For instance, if you are using a turbo yeast, you could potentially reach up to a 12-13% alcohol content. Alternatively, if you are employed a long, slow fermentation method, your alcohol content may be much lower at only 3-4%.
Ultimately, the amount of alcohol that you get from a 25 Litre wash is dependent on the fermentation process that you use.
How do you know when to stop distilling?
When distilling, it is important to know when to stop. Generally, this is determined by the look and taste of the distillate. When the desired flavor, aroma, and color has been achieved, the distillation should be stopped.
It is also important to pay attention to the temperature of the distillate. Once the consumer-desired proof has been reached it is usually time to stop distilling and transfer the liquid to separate holding tanks.
Lastly, when the volumetric flow rate of the distillate has slowed to a near standstill, this means that the vapor is no longer being carried to the condensing system and the distillation should be stopped.
Can you make rum in a T500?
No, you cannot make rum in a T500, as a T500 is a piece of office equipment, specifically a thermal printer. However, you could use a T500 for printing labels for rum bottles, as long as the printer is equipped with a label roll.
Additionally, you could use a T500 to print reports and documents that are related to making and selling rum.
When should I stop Turbo 500?
When the temperature of the boiling liquid (usually a sugar syrup) inside the Turbo 500 reaches 103°C (217°F). This is the general boiling point of sugar solution, and it’s important to allow the Turbo 500 to reach this temperature to ensure that all the sugar is completely dissolved.
Once the temperature has reached 103°C/217°F, you should then turn off the heat and remove the Turbo 500 from the heat source. You should also allow the unit to cool before opening it, as the liquid inside can still be quite hot.
What temperature should I run my T500?
The temperature you should run your T500 will depend on several factors, such as the environment you are using it in, the type of applications you are using it for, and the type of task you are using it for.
In most cases, you should aim for a temperature of around 30-40C, depending on the ambient temperature of the room. If you find that your laptop is running too hot, you may need to adjust the fan speed to reduce the temperature, or if you are comfortable doing so, you can also adjust the voltage of the processor to increase the cooling efficiency.
Additionally, if you are using the laptop for intensive tasks, you may want to opt for a higher temperature in order to keep the components within an optimal temperature range. Finally, if you are in an environment with high humidity, such as in a tropical climate, you may need to select a higher temperature in order to prevent condensation from occurring on the laptop’s components.
How much wash is left after distilling?
The amount of wash left after distilling depends on the type of distilling process being used as well as the amount of product being distilled, as well as the efficiency of the still. Generally, when distilling with a pot still, a portion of the wash will remain in the pot, whereas when using a reflux still, most of the liquid will be distilled.
In the case of a pot still, it is difficult to estimate exactly how much of the liquid will remain in the pot after distilling. This is because the amount of wash left depends on the conditions of the still, the type of still, and the length of distillation.
Generally, when using a pot still, approximately 2-15% of the wash will remain un-distilled in the boiler, although this can vary depending on the efficiency and effectiveness of the still.
When using a reflux still, the amount of wash left in the boiler is generally much less due to the efficient nature of the reflux process. Typically, when using a reflux still, only a small amount of the wash will remain in the boiler after distilling, usually less than 5%, and typically less than 1%.
Overall, the amount of wash left in the boiler after distillation depends largely on the type of still that is used as well as the efficiency and effectiveness of the still. Generally, when using a pot still, 2-15% of the wash will remain un-distilled, whereas when using a reflux still, only a small amount of the wash will remain, usually less than 5%.
How long does it take for a water distiller to work?
The time it takes for a water distiller to work varies depending on the model and size of the unit. Generally speaking, a water distiller will take between 3-6 hours to produce 1 gallon of distilled water.
Smaller models may produce the same amount of distilled water in less time, whereas larger models may take longer. The rate of production is based on the power of the unit, so the more powerful the distiller, the faster it will produce the needed amount of distilled water.
Because the water distiller is pass-through, it can be run indefinitely without needing to stop and cool down. As a result, you could have multiple gallons of distilled water within a relatively short amount of time.
Can you just boil water to make it distilled?
No, boiling water alone will not make it distilled. Although boiling will remove some impurities, it will not remove all of them. In order to make distilled water, the process of distillation needs to occur, which involves evaporating the water by boiling it, and then condensing it back into liquid form.
This process removes impurities and minerals, leaving only pure water that is suitable for many applications, such as drinking and cooking. It is also used in many industrial processes such as cooling, cleaning and manufacturing.
In order to make distilled water at home, you would need to purchase a distilling machine, which can be found at most home goods stores.
Is the T500 a reflux still?
No, the T500 is not a reflux still. The T500 is an Auckland-made stainless steel distilling unit manufactured by Still Spirits that is typically used to distill essential oils from plants. This still is commonly referred to as a Turbo still and works by boiling the plant material in a boiler, then a fan cools the vaporized oils that come off via steam and these are then condensed back into liquid form.
This process produces a higher yield of essential oils than other distillation systems. The process is not a reflux process as the vaporized oils are not condensed directly back into the same boiler and instead are cooled via the fan.
This ensures that the essential oils are not lost to the boiling system and instead are recovered.
How to make gin with Turbo 500?
Making gin with a Turbo 500 requires a bit of preparation and knowledge of the distilling process. To make gin, you must first create a base spirit, such as vodka or grain neutral spirits. You will then redistill this base spirit with juniper berries and other botanicals to impart the gin’s unique flavor profile.
To begin, you will need to properly sanitize your Turbo 500 setup to make sure there isn’t any bacteria present. After sanitizing your equipment, you will need to install the column of the Turbo 500.
This is done by attaching the column onto the boiler and then attaching silicone washers to the column.
Next, you will need to set up the condensing system. For this, you will attach the copper condenser coil to the top of the column. You will also want to connect the glycol cooling line or an ice bath if you don’t have a glycol system.
Once all of your equipment is properly set up, you are ready to begin the distillation process. Before adding your base spirit, make sure to test it for ABV to ensure it is within the acceptable range.
Next, attach both a ball valve and the product take-off arm to the top of the column. Fill the boiler with your base spirit and begin heating it up.
Once the base spirit has reached the desired temperature, it’s time to add the juniper berries and other botanicals. Place them in the flavor basket at the top of the column and connect the basket to the product take-off arm using a clamp.
During this process, you may need to adjust the flow valve to maintain the desired product rate.
Finally, turn the temperature to the desired level and let the gin distill. As it is distilling, it is important to keep a close eye on the product rate. When the product rate drops, the distillate may contain too many impurities, so it is best to adjust the flow rate to ensure the gin is of the highest quality.
Once the gin has been distilled to the desired alcohol content, you can turn off the heat, carefully disconnect the product take-off arm, and dispense your gin. Congratulations! You have successfully created delicious gin with your Turbo 500.
What temp do you run a Turbo 500?
When running a Turbo 500, the temperature should be kept between 65-85 degrees Celsius (149-185 degrees Fahrenheit). It is important to monitor the temperature throughout the distilling process to ensure there is a safe working temperature that prevents boiling over.
To make sure you are keeping the temperature in the optimal range, consider investing in a thermometer if you do not already have one, as it is essential for accurate readings and to ensure safe distilling.
Additionally, if you find yourself needing to cool down your run, you can add a few ice cubes in your collection vessel.
Where is Turbo 500 still made?
Turbo 500 is still manufactured in Australia, in a factory located in the suburb of Clayton South in Melbourne. The company’s founder, Alfred Legge, set up shop there in the 1960s, and the factory has been in operation ever since.
It’s a family-run business that has earned an international reputation for quality, reliable products. The factory produces both domestic and commercial distilling systems, along with several other alcohol-related products.
Every component is designed and manufactured in their own facility, and the company prides itself on its attention to quality, detail and craftsmanship. The turbo 500 has been widely exported to over 30 countries across the globe, and production continues to travel around the world as more and more people discover the unique flavor and convenience offered by Turbo 500.